ESP32 Projects
Step-by-step builds: smart home, sensors, relays, displays and IoT devices.

ESP32 ST7789 Example: Drive the Display with ESP-IDF esp_lcd
Step-by-step ESP32 ST7789 example using the ESP-IDF esp_lcd driver: SPI bus setup, panel IO config, esp_lcd_new_panel_st7789, verification and common mistakes.

ESP32 Wi-Fi and Bluetooth Module: What It Is and How to Start
Plain-English guide to the ESP32 Wi-Fi and Bluetooth module: chips vs modules, how both radios share one antenna, how to get started and pitfalls to avoid.

ESP32 DevKit V1: What It Is and How to Get Started
DOIT ESP32 DevKit V1 is built on the ESP32-WROOM module. Learn setup with Arduino IDE or ESP-IDF, pinout basics, and how to avoid common pitfalls.

ESP32-S3 AI Example: Build a Real-Time Voice Assistant
Step-by-step guide to building a real-time conversational AI on ESP32-S3 using LiveKit WebRTC, OpenAI Whisper, GPT-4o, and ElevenLabs TTS.

ESP32 DAC Example: Output Analog Voltage Step by Step
Learn how to use the ESP32's built-in 8-bit DAC on GPIO25 and GPIO26 with ESP-IDF. Covers one-shot, continuous DMA, and cosine wave modes.

ESP32 OLED Display: Wiring, Code and Common Pitfalls
Connect an SSD1306 or SH1106 OLED to your ESP32 over I2C or SPI. Wiring guide, Arduino and MicroPython code, and fixes for common problems.

ESP32-WROOM: How to Program It Step by Step
Learn how to program the ESP32-WROOM module using Arduino IDE or MicroPython. Covers drivers, esptool, boot mode, and common upload errors.

ESP-IDF Examples: How to Find, Build, and Run Them
Step-by-step guide to finding, building, and flashing ESP-IDF example projects on ESP32, covering hello_world, Bluetooth, build setup, and common errors.

ESP32-CAM Module: What It Is and How to Get Started
Practical guide to the ESP32-CAM module: key specs, wiring for flashing, common pitfalls, and project ideas drawn from real source data.

ESP32 Home Assistant Projects: Ideas for Every Skill Level
Curated ESP32 Home Assistant project ideas grouped by theme: sensors, displays, voice satellites, and hardware integration — for beginners and advanced makers.

ESP32 Web Server Example: Step-by-Step Setup Guide
Build a working ESP32 web server in Arduino IDE with ESPAsyncWebServer. Full example code, verification steps, periodic refresh, and common mistakes explained.

ESP32 LoRa Example: Send & Receive Messages Step-by-Step
Upload a sender and receiver sketch to two Heltec ESP32 LoRa boards, set the right frequency band, and watch packets arrive in the serial monitor.

ESP32 Bluetooth Example: BLE Scanner Step-by-Step
Run your first ESP32 Bluetooth example in Arduino IDE. Covers BLE scanner code, BluetoothSerial, RSSI, common mistakes, and what Bluetooth modes the ESP32 supports.

ESP32 TFT Display Example: Step-by-Step Setup Guide
Wire an ESP32 to a TFT display over SPI or 8-bit parallel, install the right library, and run your first display code — with verification steps and common mistakes.

ESP32 Camera Example: Step-by-Step Setup Guide
Set up an ESP32 camera module from scratch: install the driver, configure AI Thinker pins, capture JPEG frames, and dodge the most common pitfalls.

ESP32 Wi-Fi Example: Connect to a Network Step-by-Step
Step-by-step ESP32 Wi-Fi tutorial for Arduino IDE and ESP-IDF. Learn station mode, common pitfalls, and how to verify a working connection.

ESP32 OTA Example: Update Firmware Over Wi-Fi Step-by-Step
A practical ESP32 OTA tutorial: partition setup, HTTPS OTA example code, rollback safety, and the most common mistakes to avoid.

ESP32 MicroPython Examples: Step-by-Step Setup Guide
Learn ESP32 MicroPython with hands-on examples: connect I2C sensors, stream I2S audio, and call web APIs. Covers tools, wiring, and common mistakes.

ESP32 Display Example: Connect and Drive a Screen Step-by-Step
Wire a display module to ESP32, pick the right library, write example code, and flash it—covering SPI e-paper and TFT panels with verified steps.

ESP32 Servo Example: Control RC Servos Step-by-Step
Control an RC servo with ESP32 using the ServoESP32 library or MCPWM. Full code, wiring, the S2/S3/C3 frequency fix, and common mistakes.

ESP32 OLED Example: Display Text and Graphics Step-by-Step
Wire an SSD1306 OLED to your ESP32 over I2C, install the ThingPulse driver, and display text and graphics with this step-by-step tutorial.

ESP32 LED Example: Blink and PWM Dimming Step-by-Step
Learn the ESP32 LED example from a basic blink to PWM brightness control using the LEDC peripheral, with wiring tips, code, and common mistakes.

ESP32 MQTT Example: Publish & Subscribe Step-by-Step
Step-by-step ESP32 MQTT tutorial covering setup, publish, subscribe, relay control, and common mistakes using ESP-IDF and Mongoose OS examples.

ESP32 Examples: Step-by-Step Setup and Run Guide
How to find, configure, flash, and verify ESP32 examples using ESP-IDF. Covers blink, WiFi softAP, HTTP server, TCP client, and combining projects.

HASS-epaper-display: ESP32 E-Paper Smart Home Dashboard
Build a low-power 7.5" e-paper wall display with an ESP32-C3 and ESPHome showing Home Assistant weather, temps, and Proxmox stats.

AmbiSense: Build a Radar-Controlled LED System with ESP32
Build AmbiSense: a privacy-safe radar-LED system using ESP32 and LD2410. No cameras — just responsive ambient lighting controlled by proximity and movement.

EnergyMe-Home: Build a 16-Channel ESP32 Energy Monitor
Build EnergyMe-Home, an open-source ESP32-S3 smart energy meter that monitors up to 16 circuits with MQTT, Home Assistant, InfluxDB and REST API.

PadSpan HA: BLE Room-Presence Tracking for Home Assistant
Turn ESP32 boards into a full BLE room-presence system with 3D floor plans, calibration, phone tracking, and 19 views in Home Assistant.

ESPHome Weather Station: Build a Solar-Powered ESP32 Weather Station
Build a full outdoor weather station with wind, rain, temperature, and solar monitoring using ESP32 and ESPHome. Integrates directly with Home Assistant.

ESPHome Touch Panel: CYD Home Assistant Display with LVGL UI
Turn the Cheap Yellow Display into a wall or desk Home Assistant control panel using ESPHome, LVGL tiles, and 3D-printed mounts.

TamaFi: Build a WiFi-Enabled Virtual Pet with ESP32-S3
Build TamaFi, an open-source WiFi-aware virtual pet on ESP32-S3 with a 240×240 color TFT, NeoPixels, and an autonomous behavior engine.

ESPAltherma: Monitor Your Daikin Heat Pump with ESP32
Turn an ESP32 into a live heat pump monitor. ESPAltherma reads your Daikin Altherma via the X10A port and streams data to Home Assistant over MQTT.

Shrike-fi: ESP32-S3 Meets FPGA on One Affordable Board
Build reconfigurable hardware projects with the Shrike-fi, a low-cost dev board pairing an ESP32-S3 with a 1120-LUT FPGA for IoT and digital design.

awesome-esp32: Hand-Picked ESP32 Projects Worth Building
A curated, device-tagged list of 40+ ESP32 projects across AI companions, displays, games, robots and radio — with guides to get you building fast.

WLED Wemos Shield: Build a Wi-Fi LED Controller for ESP32
Turn a Wemos D1 Mini into a full-featured Wi-Fi LED controller with the open-source WLED Wemos Shield PCB. Level shifter, relay, OLED, and more.

Project Aura AQ: ESP32-S3 Air Quality Monitor with Home Assistant
Build a polished ESP32-S3 touchscreen air quality station with PM, CO2, VOC, HCHO sensors, MQTT, Home Assistant integration, and no cloud dependency.

Nuki Hub: Turn an ESP32 into a Smart Lock Bridge
Flash Nuki Hub to an ESP32 to bridge any Nuki Smart Lock or Opener to Home Assistant, ioBroker, FHEM and more over local MQTT.

ESP32 Web Radio & Bluetooth Speaker with MP3 Decoder
Build an ESP32 internet radio and Bluetooth speaker that decodes MP3 and AAC streams over Wi-Fi and outputs audio via I2S codec or built-in DAC.

IKEA OBEGRÄNSAD ESP32 Hack: Turn a Lamp into a Smart LED Canvas
Replace the stock controller in an IKEA OBEGRÄNSAD lamp with an ESP32 for Wi-Fi pixel art, 20+ plugins, a REST API, and Home Assistant support.

ESPHomeDesigner: Visual Drag-and-Drop ESP32 Display Editor
Design custom dashboards for ESP32 E-Ink, OLED, and LCD displays without writing display code. Runs inside Home Assistant or as a standalone web app.

NumOS: Build an ESP32-S3 Scientific Graphing Calculator
Build NumOS, an open-source scientific graphing calculator OS on the ESP32-S3 with a color TFT display, CAS engine, and natural math rendering.

Build Smart Interfaces on M5Stack with M5ez
Learn to build responsive UI applications on M5Stack ESP32 using M5ez interface builder library. Create menus, buttons, text input and WiFi apps.

Home Assistant Glow: ESP32 Energy Monitor Build Guide
Turn any electricity meter's pulse LED into real-time energy data in Home Assistant using an ESP32, ESPHome, and the Home Assistant Glow project.

ESPTimeCast: Build a WiFi LED Matrix Clock and Weather Display
Build ESPTimeCast on ESP8266 or ESP32 with a MAX7219 LED matrix. Flash from your browser in minutes — no IDE needed. Shows live time and weather.

NightDriverStrip: ESP32 LED Effects Firmware Build Guide
Flash NightDriverStrip to an ESP32 and drive WS2812B or HUB75 LEDs with audio-reactive effects, WiFi control, and a live web UI.

PocketMage PDA: Build an E-Ink PDA with ESP32-S3
Build the PocketMage PDA — an ESP32-S3 powered clamshell device with E-Ink and OLED displays, a custom OS, text editor, file manager, and more.

ESP32 E-Paper Weather Display: Build Guide (esp32-weather-epd)
Build a low-power E-Paper weather station with an ESP32, BME280 sensor, and OpenWeatherMap API. Runs 6–12 months on a single battery charge.

ESP32 Cheap Yellow Display (CYD): Complete Build Guide
Build projects with the ESP32-2432S028R Cheap Yellow Display — a $15 ESP32 board with a 2.8" touchscreen, Wi-Fi, and Bluetooth, no soldering needed.